FENIX GL06 Picatinny MIL-STD (600lm.) GL06

The Fenix GL06 pistol LED light is specifically designed for use on short firearms equipped with a Picatinny MIL-STD-1913 and Glock standard rail. It offers a maximum light output of 600 ANSI lumens with a range of up to 140 meters. The light is powered by a single Li-ion Fenix ARB-L16-700UP battery with an integrated micro USB connector (battery and cable are included in the package). If needed, a single-use CR123A lithium battery can also be used. The simplified control of the light is ambidextrous (for both right-handed and left-handed users). Mounting on the weapon rail is easy and tool-free - the light slides onto the rail and is secured with a lever. It can be attached to Picatinny MIL-STD-1913 and GLOCK standard weapon rails (not suitable for slimline category weapons, e.g. Glock 30 model). Compatible with service weapons of the Police of the Slovak Republic (CZ 75D). The light is suitable for professionals, sports and hobby shooters, as well as airsoft enthusiasts.

All parameters of the light (luminous flux, battery operating time, waterproofness, range, and impact resistance) are measured in accordance with the ANSI/NEMA FL 1-2009 standard.

Parameters:
- Premium CREE XPL HI LED with a lifespan of 50,000 hours is used.
- Lighting modes:
1. With Fenix ARB-L16-700UP battery: 600 lumens (50 minutes) -> strobe.
2. With a single CR123A battery: 400 lumens (1.5 hours) -> strobe.
- TIR optics create a beam with a range of 140 meters (4880 cd) - measured when using the supplied battery.
- Protection against reverse battery insertion and protection against deep discharge of the battery.
- It uses a single Li-ion Fenix ARB-L16-700UP battery (included in the package) for power, alternatively, other Li-ion RCR123A / 16340 batteries can also be used.
- Additionally, a single-use lithium CR123A battery can be used, but the light with it has reduced output to 400 lumens.
- Dimensions: 6.1 cm (length) x 2.8 cm (height) x 2.3 cm (width).
- Weight 69 grams (including the battery).
- Compatible with Picatinny MIL-STD-1913 and GLOCK weapon rails.
- Intelligent overheating protection.
- Body of the light made of aerospace-grade aluminum.
- Resilient hard anodized Type III surface.
- Impact-resistant from a height of 1 meter.
- Trapezoidal threads highly resistant to wear.
- Waterproof according to IPX7 standard (tested underwater at a depth of 1 meter).
- The package includes Fenix ARB-L16-700UP battery, charging micro USB cable, Picatinny rail mount latch (GLOCK latch is pre-installed on the light), spare O-ring, and manual.

Control:
There may be an insulating cover inside the light on the battery. Remove it from the battery before first use.

A single click on any of the switches turns the light on/off.

For momentary activation, press and hold any switch. The light will illuminate while the switch is held, and will turn off when the switch is released.

Strobe activation: Pressing both switches simultaneously activates the strobe. The strobe can also be activated by pressing and holding one switch and clicking the other switch. Pressing one switch again will end the instant strobe mode, or pressing both switches simultaneously will return to the last used output.

Intelligent overheating protection: When the light is used for an extended period, a large amount of heat accumulates. When the light reaches a temperature of 55°C or higher, it automatically reduces the output by a few lumens to lower the temperature. When the temperature drops below 55°C, it returns to the standard output.

Warning:
- Do not disassemble sealed parts in the head of the light yourself, as it will void the warranty and may cause damage.
- Fenix recommends using only high-quality batteries.
- If the light will not be used for an extended period, remove the battery.
- If the light's lens is contaminated with residues after shooting, try cleaning it with fine steel wool or use gun cleaning paste.
- Long-term use may result in wear of the O-ring. To maintain proper water sealing, replace the ring with a new one.
- Since firearm maintenance requires the use of organic solvents, avoid contaminating key parts of the light. This could damage the light and void the warranty.
- Regular cleaning of electrical contacts ensures smooth operation of the light, as contaminated contacts can cause the light to flicker, illuminate intermittently, or not illuminate for the following reasons: The battery is depleted - replace or recharge it.
- Contacts inside the light are dirty - clean them with a cotton swab soaked in alcohol.